| Ref
# |
Pic |
Equipment
Description |
Note |
Sales
$ |
| 39.0019
|
|
Yates 177 12"X30" 2-side planer, 550V motors not included, requires 15 HP 3600 RPM (bottom), 40 HP top (direct), 5 HP feed (1200 RPM), never operated since complete rebuild by Chism. 60, 125, 135, 165 fpm. No feed table. |
|
$20,750
|
| 39.0093
|
|
Whitney dbl surface planer, 7"X26", round head, ball bearing, knife sharpener. |
|
$4,000
|
| 39.0094
|
|
8"X24" single surface planer, square heads, babbit , drive shaft for tractor PTO. |
|
$1,200
|
| 39.0096
|
|
Newman M68, S/N 10977, 4 side planer 6"X16", 4 knife round head, Ball Brng., belt driven, 1 set straight side heads. Currently operating. |
|
$24,900
|
| 39.0103
|
|
Complete set of NELMA Pattern #2 taper side heads & profile heads (some L knife - some straight knife). |
|
POR
|
| 39.0108
|
|
Co-T (Canadian) moulder, 2-1/2"X6" 4Hd (Rd), BB moulder, reconditioned, w/motors/controls |
|
$4,500
|
| 39.0111
|
|
Woods 412 profile heads (2) and a pineapple feed. |
|
POR
|
| 39.0113
|
|
Yates A4 planer, 6"X15", ball bearings, 4 head, 4 sider, 4 sets knives. 3 sets side heads: T&G, 4" flat, 2 eased edge. |
|
CD $14,000
|
| 39.0116
|
|
Wadkin Moulder, Model SD214, Four heads, Max. board 4" X 4". |
|
POR
|
| 39.0119
|
|
Newman M-712 planer s/n 130250, year 1972, 8 knifew top and botom cylinders, (2) 35 HP motors top head, 35 HP bottom, 40 HP left side head, 25 HP right side head. Hydraulic power pack feed, each feed roll equipped with hydraulic motor, one pair of 8-knife 2" S4S side heads, no side head hold downs or side head. 550volt. |
|
$60,000
|
| 39.0124
|
|
Yates American A-20 planer, 8"X12", direct drive |
|
$33,500
|
| 39.0127
|
|
Porter 800 leveller-jointer to flatten cup/crown on boards. |
|
POR
|
| 39.0128
|
|
Planer infeed table |
|
POR
|
| 39.0131
|
|
Stetson-Ross 31-M Travelling Carriage Timber Surfacer. Capacity: 36inx18inx40feet. Sq. heads with ball bearings. Main head tilts 15 degrees, side head tilts from 15deg pos. to 45deg neg. Main head is driven by two 20HP direct drive motors. Side head is driven by one 20HP direct drive motor. 440V. Excellent condition. Use for surfacing timbers for post and beam as well as boat building. Very few of these machines were built and only a couple are in private hands. Machine is close to 10 feet tall, nearly 100 feet long, all steel and cast iron. |
|
$9,000
|
| 39.0132
|
|
Planer Mill: Just rebuilt at P B Yates, Hamilton ON--1960 A-20 8 knife, double profile; new bed plates 1990, average 1,000,000 production/year; Belt drive but set up for full electrics; A-B Auto Starter; Atelier (Longueil,QC) Infeed 36" angled rolls electric drive; 3/60/600; Yates V-54 Splitting resaw w/35' Infeed rolls; Blower system all pipes; Outfeed 22' belt; 3 strand 14'-81X electric transfer; Filing room w/ Hanchett grinder, spare heads, complete with tools etc. (Description and photos continued under 39.01321 below) |
|
POR
|
| 39.01321
|
|
(Continued from 39.0132 above) Filing room w/ Hanchett grinder, spare heads, complete with tools etc. |
|
|
| 39.0137
|
|
A) Yates Planer infeed, 2 pineapple feed rolls, 6"X 30" spiral feed rolls 6' OC. B) Newman 500 6"X15" planer, 6 knife, bottom profiler, belt driven. |
|
POR
|
| 39.0138
|
|
Vance L-6 4-side planer, 6"X16", w/pineapple feed table, 6 Knife round head, bottom profile, ball bearing, flat belt drive, extra heads V-match etc. 75 HP 3 phase motor. |
|
POR
|
| 39.014
|
|
Woods 4 side planer, rebuilt-have paperwork. |
|
$4,500
|
| 39.0142
|
|
Leadermac Model 523C 5 head high speed moulder (1999). 6"X9", 440V. |
|
POR
|
| 39.0143
|
|
Planer, A-20-12, 8 knife 4 sider w/feed table & double profiler, located in Quebec City. |
|
POR
|
| 39.0144
|
|
Oliver 2 side planer, 13X30(Est.), table has up-down automatic. |
|
POR
|
| 39.0145
|
|
Yates A-20 planer, 8"X12". |
|
$25,000
|
| 39.0146
|
|
Newman 510 planer and pineapple feed. (Worn but good for small producer). |
New Listing
|
POR
|
| 39.0147
|
|
Profimat 22N molder |
New Listing
|
POR
|
|
|
|
